Custom Windows & Doors in Ocean Ridge - Free In-Home Measure, Written Price

Fast, Reliable Custom Windows & Doors Across Ocean Ridge

Custom windows and doors in Ocean Ridge are not a commodity purchase. This town sits on a barrier island with salt air coming at every property from two directions at once, the Atlantic on the east and the Intracoastal on the west. The hardware, frame finishes, and glass-edge seals that hold up inland fail early here. We have been replacing those failed components and spec-ing the right ones the first time for homeowners across Ocean Ridge for years. If you are pricing a full replacement or a custom-shaped window or an oversized glass panel, call (850) 801-5596 and we will walk the openings with you and put a line-item quote in your hand.

Why TruePane Windows & Doors Is Ocean Ridge’s Preferred Custom Windows & Doors Company

We have earned our place in Ocean Ridge one opening at a time. The homes here are almost entirely single-family CBS construction, many built between the 1950s and 1970s, and a large share of them still carry original jalousie or single-pane aluminum windows that never met Florida’s post-Andrew impact codes. Our Custom Windows & Doors crew knows what those openings look like when we pull the old frames: pitted aluminum, seized louvers, crumbled weatherstripping. You learn that by doing the work, not by reading a spec sheet.

Ocean Ridge homeowners call because they want a company that will still answer the phone after the install. Dale Kessler founded TruePane on the rule that if the pane is not true, the job is not done. That applies to warranty registration too. Every job carries The Keystone Standard: both manufacturer warranty layers registered in writing, durations stated, before the truck leaves your driveway. And our Done Right Promise means if something is not right, we make it right without a paperwork battle.

Our installers are background-checked and uniformed. They measure every opening twice. They quote manufacturer lines side by side on paper so you see exactly what you are buying. For custom windows and doors in Ocean Ridge, that level of care is not a preference. It is the minimum the environment demands.

Our Custom Windows & Doors Services in Ocean Ridge

Custom Shape Windows

Ocean Ridge has a high concentration of mid-century and custom coastal homes with arched, circular, eyebrow, and angled openings. Off-the-shelf rectangular windows cannot fill those openings without awkward framing or oversized trim. We measure the actual radius of the opening, not a template, and order the custom-shaped unit to the eighth of an inch. In salt-exposed Ocean Ridge locations we spec marine-grade frame finishes and 316 stainless hardware as the default, because a standard aluminum custom window will show white corrosion on the fasteners within 18 months here.

Oversized Glass Panels

Most Ocean Ridge owners want the water view. Oversized fixed glass panels deliver it, but they are heavy and the wind load calculations here are serious. Palm Beach County’s coastal high-wind design zone requires glazing sized to meet significant design pressure ratings on every replacement. We size the IGUs for thickness and span, then order the glass from manufacturers who certify their products for Miami-Dade and Palm Beach wind loads. The frame on an oversized panel facing the Intracoastal carries the same hardware spec as our ocean-facing installs: hot-dip galvanized or 316 stainless, period.

Architectural Grilles & SDLs

Simulated divided lites give a traditional look with the thermal performance of a single IGU. In Ocean Ridge, we see a lot of SDLs on front elevations and interior doors where the homeowner wants the old coastal cottage look without the heat loss of true divided lite construction. The key detail here is the seal. A poorly sealed SDL cavity traps salt-laden air against the glass and frame. We order SDLs from lines that engineer the grille pocket to drain and breathe, and we register both warranty layers in writing on every job.

Commercial Storefront Glazing & Curtain Wall Systems

Most of Ocean Ridge is residential, but the small commercial and HOA clubhouse buildings along A1A and the Intracoastal frontage still need curtain wall and storefront work. Salt air eats standard aluminum mullions and pressure plates faster here than almost anywhere else in the county. We specify thermally broken aluminum with a marine-grade anodized or powder-coated finish and stainless fasteners throughout. We also handle glass railing systems for oceanfront and Intracoastal balconies, where spalling and rust on cheap hardware fails within a few seasons and becomes a safety issue.

Trusted Brands We Service in Ocean Ridge

We are an authorized installer for more than a dozen manufacturer lines, and we order and service CWS, ES Windows, and ECO Window Systems for Ocean Ridge work. All three build impact-rated products that hold up in severe marine environments when spec’d correctly, and all three back their glass and frames with written warranties we register for you. Because we work with these brands continuously, we can often get custom sizes and replacement IGUs turned around faster for Ocean Ridge customers than a shop that orders occasionally. We also quote side by side on paper, so if you want to compare a CWS impact unit against an ECO Window Systems impact unit for the same opening, you will see the difference in writing before you spend a dollar.

Common Custom Windows & Doors Problems We See in Ocean Ridge Homes

• Seized jalousie louvers: The original jalousie windows from the 1950s through the 1970s have zero impact rating and no effective weatherstripping. Decades of salt air pit the aluminum louvers until they bind shut or rattle open in a storm. We recently pulled the original jalousies from a 1960s CBS home on Tropical Drive and found the frames so pitted that the louvers had seized, the homeowner was using a pry bar just to get air. Those openings got full impact-rated casement and picture units, fusion-welded vinyl frames, 316 stainless hinges, and sealed jamb pockets.
• Rusted sliding door hardware: Non-marine-grade stainless or zinc-plated hardware on sliding doors and casement operators corrodes within two to three seasons on a barrier island. Locks bind, hinges snap, and rust streaks run down the stucco. We replace the hardware and often the frame itself with fully corrosion-resistant spec.
• Premature glass seal failure: In IGUs without marine-rated edge seals, salt fog infiltrates the spacer bar and kills the seal early. The homeowner sees fog between the panes because the argon has escaped, and the glass loses most of its insulating value. On Ocean Ridge jobs we specify marine-rated edge seals and verify the spacer bar on every unit we order.
• Non-compliant openings on renovation projects: When a permit is pulled for any substantial renovation, the original jalousie or single-pane aluminum windows get flagged as non-compliant under current Florida Building Code wind-load standards. That means full-opening replacement, and our job is to make the new spec correct the first time, no change orders after the walls are open.

Pricing for Custom Windows & Doors in Ocean Ridge, FL

We Also Serve Cities Near Ocean Ridge

TruePane crews serve Ocean Ridge and the surrounding South Florida coastal communities including Palm Beach, Lake Worth Beach, Westgate, and Palm Springs. If you are across the bridge or a few miles south, the same crew, the same warranty registration, and the same Done Right Promise apply. We schedule Ocean Ridge jobs directly from our local crew so you are not waiting on a dispatcher three counties away.

FAQs - Custom Windows & Doors in Ocean Ridge

Why do window and door jobs cost more in Ocean Ridge than the same job just across the bridge in Boynton Beach?

Because the salt air here comes from two directions at once. Ocean Ridge sits on a barrier island with the Atlantic on one side and the Intracoastal on the other, so every property gets continuous salt spray exposure that does not exist on the mainland. The marine-grade frames, 316 stainless hardware, and sealed jamb pockets that keep an Ocean Ridge window functional for a decade cost more than the inland-spec components used in Boynton Beach. The inland-spec version of the same job may run 10 to 18 percent less up front, but the hardware will start corroding within 18 to 36 months and you will replace the unit long before the warranty expires. Call (850) 801-5596 and we will quote both specs side by side in writing so you see exactly what you are paying for.

Are original jalousie windows in Ocean Ridge ever worth keeping, even with new weatherstripping?

No. The original jalousie windows from the 1950s through the 1970s have zero impact rating and no effective weatherstripping, and after decades of salt air aboard Ocean Ridge the aluminum louvers are commonly pitted and seized. No amount of new weatherstripping fixes a seized louver that cannot close tight, and the opening still fails Florida Building Code wind-load and impact requirements. Any substantial renovation that pulls a permit will flag them for replacement. We replace full jalousie openings with impact-rated casements, picture units, or custom shapes sized to fit the existing opening, and we register every warranty layer in writing before leaving.

What kind of hardware should I spec for a sliding glass door that faces the Intracoastal side in Ocean Ridge?

Spec hot-dip galvanized or 316 stainless hardware on the rollers, tracks, hinges, and locks, and do not accept zinc-plated hardware as a cost-saving substitution. The Intracoastal side gets just as much salt air as the ocean side, and ordinary zinc-plated hardware on sliding doors will rust, bind, and leave streaks down the stucco within two to three seasons. We default to 316 stainless or hot-dip galvanized on every Ocean Ridge job, and we order marine-grade frame finishes so the aluminum itself does not start pitting at the weep holes.

Why does my ‘brand new’ double-hung window already have fog between the panes after one year in Ocean Ridge?

That is a failed insulated glass unit seal, caused by salt fog infiltrating the spacer bar in the IGU. It happens in Ocean Ridge when the glass was ordered without a marine-rated edge seal, or when a less expensive spacer bar was used. The fog between the panes means the argon or krypton gas has escaped, and the unit has lost most of its insulating value. The fix is a replacement IGU with a marine-rated edge seal and a spacer bar rated for severe marine environments. We can order and install replacement IGUs for Ocean Ridge homes, and we will register the replacement glazing warranty in writing.

Do I really need impact-rated glass on every window, or just the ones facing the ocean?

Every window and door opening in Ocean Ridge needs impact-rated glazing, not just the ocean-facing ones. The entire town falls within Palm Beach County’s coastal high-wind design zone, and the Florida Building Code requires impact-rated glazing and door systems on all replacements and new installs regardless of which direction the opening faces. The Intracoastal side generates wind-driven spray just like the ocean side, and storm winds arrive from multiple directions. Skipping impact-rated glass on one side of the house leaves the entire envelope weaker and fails code. Call (850) 801-5596 for a free estimate; we will spec every opening to current code and register the warranties in writing.

Written by Dale Kessler, Owner at TruePane Windows & Doors, serving Ocean Ridge and the surrounding South Florida coast.