Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterHorizontal Roller & Sliding Windows in Palm Beach, FL | TruePane Windows & Doors
Horizontal roller and sliding windows are a natural fit for Florida homes: wide sightlines, easy one-hand operation, and a profile engineered for hurricane country. In Palm Beach, where coastal exposure turns window openings into the most vulnerable part of the envelope, this profile earns its keep. Our workhorse impact series glides on a reinforced track and carries laminated impact glass tested to withstand 140-mph winds and 9,500 lbs of wind-borne debris impact. TruePane Windows & Doors installs these across our PGT, CGI, CWS, ES Windows, ECO, and Mr-Glass lines, and we set every unit level, plumb, and square against Florida’s High-Velocity Hurricane Zone requirements. If you’re pricing impact sliders for a Palm Beach remodel or replacement, call (850) 801-5596 for a free on-site measurement and a written quote.
Product Overview - Horizontal Roller & Sliding Windows
This profile exists for one reason: to let in light and air while standing up to the worst weather Florida can throw at it. The horizontal roller and sliding window is the most common moving-glass opening in Palm Beach bedrooms, kitchens, and family rooms because it pairs a clean, minimalist frame with hardware that stays easy to operate even at large widths. Where a fixed picture window stops the storm but not the breeze, a slider gives you both.
What separates an impact-rated slider from a standard one is the lamination. Our units use laminated impact glass with a PVB (polyvinyl butyral) interlayer, so even if wind-borne debris strikes the pane, the glass fractures but stays held in the frame. That’s the difference between a window that keeps your home sealed during the storm and one that fails the moment it’s hit. The reinforced track and interlocking frame members are sized and tested as a system, not as individual parts bolted together.
Architecturally, this is the profile that works hardest in mid-century Palm Beach ranches, 1970s and 80s concrete-block homes, and newer coastal builds alike. It reads as horizontal, keeps sightlines low and wide, and in a 3-track configuration still delivers strong ventilation to living areas. When we install it in Palm Beach, we’re typically replacing the builder-grade sliders that leaks and stick after ten years of salt air. The difference in glide, seal, and frame rigidity is immediate.
Technical Specifications
- Frame materials: Aluminum or vinyl, selected to match your existing structure and exposure. Aluminum is our typical recommendation on Palm Beach oceanfront and intracoastal elevations for its rigidity; vinyl carries strong thermal performance and lower upkeep inland.
- Track configurations: 2-track (two panels, one moving) or 3-track (three panels, center-vents wider), chosen by opening width and how much ventilation you want.
- Glass options: Laminated impact glass with PVB interlayer, Low-E insulated glass, tinted glass, or clear glass, in combinations that fit your wind zone and energy goals.
- Finish options: White, almond, bronze, black, and tan, across painted and anodized-style finishes depending on line.
- Screen options: Retractable screen or standard sliding screen for bug pressure and daily ventilation.
- Design pressure: Matched to your wind zone, up to +/-100. We do not over-spec beyond the number your structure needs.
Hurricane & Compliance Performance
Laminated Impact Glass - The PVB interlayer holds broken glass in the frame under impact, which is the single most important safety feature in a Palm Beach coastal opening. Without it, one piece of flying debris turns the window into a pressure-opening failure point. With it, the envelope stays sealed.
Miami-Dade NOA / Florida Product Approval - Every configuration carries the required Notice of Acceptance and Florida Product Approval numbers under Miami-Dade County’s protocol. The specific number applies to your exact size and configuration, so we verify it on your written quote, not with a generic catalog page.
FBC / HVHZ Compliance - The product is engineered to Florida Building Code High-Velocity Hurricane Zone requirements. Palm Beach sits inside the HVHZ map, which means this is not an optional rating. It’s the minimum bar for legal installation here.
TAS 201 / 202 / 203 Testing Context - HVHZ-rated products are tested under a family of protocols: TAS 201 for large-missile impact, TAS 202 for cyclic wind-pressure loading, and TAS 203 for forced-entry resistance. That sequence simulates what a storm does to a window over hours, not seconds.
Design Pressure Matched to Your Wind Zone - We size design pressures to your building’s location and exposure, up to +/-100, never higher. Over-specifying costs you money without adding real safety, which is why our quotes show the number your opening actually requires.
Energy Performance Options - Low-E and insulated glass configurations are available on this profile for homeowners who want the impact rating plus solar control. In Palm Beach, we see this combination most often on west-facing elevations and rooms that run warm in the late afternoon.
Color & Glass Options
Color is the first thing most Palm Beach clients choose, and the coastal palette here does the narrowing for you. White and almond frames read crisp against pastel stucco and stay the default on older Spanish-Mediterranean homes. Bronze and black have taken over new construction and modern renovations, especially where the window frames contrast with white or sand-colored walls. Tan is the quiet option on beige and terra-cotta exteriors where you want the frame to disappear into the wall. All finishes are available across the aluminum and vinyl lines we install through our PGT, CGI, CWS, ES Windows, ECO, and Mr-Glass series.
Glass selection follows exposure and room use. Clear laminated impact glass is the economical workhorse for bedrooms and less sun-blasted elevations. Tinted glass cuts afternoon glare and solar gain on east and west faces. Low-E insulated glass is the pick where you want single-pane impact protection plus meaningful heat reflection, and it’s what we recommend most often on Palm Beach homes with large south-facing slider banks. The laminated interlayer stays present in every option, so you’re never choosing between code compliance and comfort.
Installation by TruePane Windows & Doors in Palm Beach
A window with a Miami-Dade NOA is only as good as the opening it’s sealed into. We’ve pulled impact sliders out of Palm Beach homes where the unit itself was fine and the installation was the failure point: no perimeter seal, shims missing at the sill, a frame racked because it was forced into an opening that wasn’t square. That’s why our installers start every job with a pre-install inspection of the rough opening, checking the existing buck or block condition and measuring for level, plumb, and square before the first fastener goes in.
On the day of installation, each unit is set, shimmed, and squared within tolerance, then anchored and sealed with AAMA 812 low-expansion foam around the perimeter. Our practice follows AAMA 2400 and 2410 installation standards, which govern exactly how a window gets installed in a coastal Florida opening. After the foam, the exterior receives the weather-resistant barrier and sealant sequence the opening calls for, and we run a final water test before interior trim goes back on. The site is cleaned on the same visit.
There’s a permitting reality in Palm Beach worth knowing up front. HVHZ jurisdictions require the correct Florida Product Approval or NOA documentation attached to the permit packet. We identify the right approval number for each configuration on your quote, and we flag any opening-specific conditions before installation starts. Improper installation doesn’t just perform worse. It invalidates the very documentation that makes the window legal.
Frequently Asked Questions - Horizontal Roller & Sliding Windows
Design pressure is matched to your specific wind zone, up to +/-100, and never higher than what your structure calculates out to require. The product itself carries Miami-Dade NOA and Florida Product Approval numbers per configuration, so the correct rating for your opening will be shown on your written quote. Call (850) 801-5596 and we’ll calculate it from your address and elevation.
Lead time depends on the manufacturer (PGT, CGI, CWS, ES Windows, ECO, or Mr-Glass) that your selected frame, glass pack, and finish routes to. Once we confirm your size and configuration, we’ll give you a written production window before you sign. We don’t hold a deposit and then surprise you later. Call (850) 801-5596 for a real production estimate based on your actual opening dimensions.
Yes, in Palm Beach and everywhere else inside the HVHZ map, your permit packet requires the Florida Product Approval or NOA number for the exact configuration being installed. We pull the correct approval documentation for each unit and verify it on your quote, so the permit office sees the paperwork matching the actual delivered window. Call (850) 801-5596 if you’re mid-permit and need the number for a specific size.
Yes, within the tested size range of each line. Width, panel count, 2-track versus 3-track, finish, glass package, and screen type are all selectable. What you can’t do is build a size outside the manufacturer’s approved envelope, because then the NOA no longer covers the unit. We’ll spec your opening to the largest tested configuration that fits. Call (850) 801-5596 with your rough opening dimensions and we’ll tell you what’s approved.
For aluminum, wash with mild soap and water and keep the track free of sand and salt. Avoid abrasive cleaners on the finish. For vinyl, same routine with a non-abrasive cloth. The rollers and track should stay clear of debris, and the weep system needs to keep draining. In Palm Beach, that’s the maintenance item that prevents most sliders from failing early. If you’re inspecting a slider that’s gotten stiff or cloudy between the panes, call (850) 801-5596 and we’ll tell you whether it’s a maintenance fix or a replacement.
Get a Quote - Horizontal Roller & Sliding Windows in Palm Beach
If you’re comparing impact sliders for a Palm Beach project, we’ll measure your openings, spec the right track and glass package for your wind zone, verify your approvals, and give you a written line-item quote. No pricing games, no change orders. Call (850) 801-5596 to schedule your free on-site measurement.
Written by the team at TruePane Windows & Doors, installing hurricane-impact windows and doors across Palm Beach, FL.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.
Other TruePane Windows & Doors Services
What Neighbors Say About TruePane Windows & Doors
Detailed Images
