Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterTherma-Tru Roof Repair in Palm Beach: What to Know First
Therma-Tru roof repair in Palm Beach typically costs between $185 and $520 depending on which component failed and whether we’re replacing hardware, weatherstripping, or the door panel itself. Most Therma-Tru jobs are completed in a single visit, and we carry the common failure parts on the truck. If you’re dealing with a roof-scalp flashing failure or a warped door that’s letting water into your entryway, call (850) 801-5596 and we’ll give you a straight answer on what it will take.
This page is for Palm Beach homeowners who own a Therma-Tru entry system and have noticed water staining around the roof line, a door that drags against the frame, or daylight showing where there shouldn’t be any. We’ve serviced these doors across Palm Beach, West Palm Beach, and the barrier islands long enough to know which problems are twenty-minute fixes and which ones mean the door has lived past its useful life.
How Therma-Tru Products Fail - and How We Fix Them
- Classic-Craft and Fiber-Classic top-sweep separation. These two lines account for most of the Therma-Tru doors in Palm Beach homes built between 1995 and 2015. The roof cap on these units is a composite threshold cap that sits over a treated wood core. After enough humidity cycles, the cap separates from the core at the outer corners. You’ll see it as a hairline gap at the top corners of the door that opens and closes with the seasons. Our fix is to pull the cap, address any rot in the core if it’s still sound, and re-set the cap with a proper sealant bed and mechanical fasteners, not just caulk.
- Roof-scalp flashing failures on Therma-Tru sliding patio systems. Therma-Tru’s sliding patio door line uses an aluminum roof-scalp flashing that gets brittle after a decade of Palm Beach sun. The flashing cracks at the screw points, then water follows the screws into the frame. We replace the flashing with a heavier gauge than factory spec and use stainless fasteners with a butyl tape bed. Factory parts fail the same way again; we’d rather not come back twice.
- Warped door panels on dark-painted Therma-Tru units facing west. A Therma-Tru door painted black or dark bronze on a western exposure in Palm Beach absorbs enough afternoon sun to bow the panel. The tell is a door that’s square at the top and dragging at the latch-side bottom corner. This is not a hinge adjustment problem, and adjusting the hinges to chase the warp just moves the gap to the top. We evaluate the panel, and if the warp is within Therma-Tru’s tolerance we re-shim the frame. If it’s past tolerance, the honest answer is a new slab.
- Compression weatherstrip collapse on Therma-Tru door bottoms. The bottom sweep on a Therma-Tru door is a vinyl compression strip that flattens over time. In Palm Beach, where afternoon downpours hit door thresholds at a low angle, a flattened sweep means water drives under the door and pools on your entry tile. This is a twenty-minute repair with the correct OEM-profile replacement. We keep several profiles on the truck because the sweep for a Classic-Craft is not the same as the one for a Pulse or a Shaker.
- Threshold and sill rot at the roof line on raised-entry Palm Beach homes. Homes built on the Intracoastal side of Palm Beach often have entry doors elevated three or four feet off grade, and those roof-scalp areas catch the full force of salt-laden east wind. The Therma-Tru threshold is a wood core wrapped in a composite cap. When the cap gets a pinhole, saltwater intrusion rots the core from the inside while the outside looks fine. We find this by pressing the threshold with a screwdriver handle. Soft means rot, and we replace the threshold to spec rather than patching it.
Our Therma-Tru Roof Repair Process
- 1
The call. You describe what you’re seeing. We ask the right questions: which side of the door, when it started, whether it’s worse after rain or after sun. That tells us a lot before we even leave the shop.
- 2
The inspection. We arrive with the common Therma-Tru parts on the truck. We measure the door, check the reveal on both sides and the top, press the threshold, and run a moisture probe if we suspect rot behind the frame.
- 3
The parts decision. OEM where it matters for warranty continuity and fit, quality aftermarket where the factory part is a known repeat failure. We show you both options on paper before we turn a screw.
- 4
The repair. We do the work in place when we can, pull the door when we must, and protect the opening while we’re in it. Two measurements before anything gets cut, per Dale Kessler’s shop rule: if the frame is right and the glass is rated, the rest is just following through.
- 5
The test and the cleanup. We cycle the door, check the sweep with a flashlight at the threshold, run water over the roof-scalp if you’ll allow it, and leave the entry cleaner than we found it.
- 6
The paperwork. The Done Right Promise applies to every Therma-Tru repair, and if a manufacturer warranty layer is relevant to the repair we register it before the truck leaves your driveway.
What Therma-Tru Roof Repair Costs in Palm Beach
Here’s the honest range based on what we’ve charged across Palm Beach County for Therma-Tru work over the last several years:
- Bottom sweep or weatherstrip replacement: $85 to $185, parts included
- Roof-scalp flashing replacement (sliding patio): $220 to $390, depending on access and length
- Top cap re-set with sealant and fasteners: $180 to $340
- Threshold replacement with rot repair: $320 to $640
- Full slab replacement (Classic-Craft or Fiber-Classic): $1,100 to $2,400 installed, depending on size and glass package
What moves the price: whether rot has spread past the threshold into the subfloor, whether the door is a custom size, and whether the home is on the barrier island where salt exposure means we’re replacing more than we’re patching. We give the number in writing before work starts, and the number we quote is the number you pay. Call (850) 801-5596 for a free estimate on your Therma-Tru roof repair in Palm Beach.
Why Palm Beach Homeowners Call TruePane Windows & Doors for Therma-Tru Work
Dale Kessler grew up in El Cid and has spent two decades measuring, setting, and servicing doors across Palm Beach County. We’re an independent Therma-Tru service provider, which means we’re not tied to a manufacturer script. If the factory part has a known failure pattern, we’ll tell you and use a better one. If the door has life left in it, we fix it and say so. If it’s done, we say that too, and we’ll walk you through the numbers on replacement with the same honesty.
We work on other lines too, including PGT, CGI, CWS, and ES Windows, so when a Palm Beach home has mixed products we service the whole entry system in one visit rather than juggling a second contractor. Every repair is covered by the Done Right Promise: if it’s not done right, we make it right, no paperwork argument, no fine print. A live person answers our phone 24/7. Call and you’ll talk to someone who can answer questions about Therma-Tru, not a dispatch service.
FAQs
No, not when the repair is done by an independent Therma-Tru service provider like us, and not for the repairs we perform. Therma-Tru’s warranty covers the door slab and factory components, not installation workmanship, and a properly done repair using correct fasteners and sealants does not void anything. We document every repair, and if the original warranty is still in effect we’ll register the applicable layer before we leave.
Most Therma-Tru roof repairs in Palm Beach are scheduled within a few days, and many common repairs like sweeps, weatherstripping, and flashing are completed in a single visit. We carry the common failure parts on the truck, so we’re not ordering and returning. Call (850) 801-5596 and we’ll give you a straight answer on scheduling.
That depends on the panel, not the hardware. If the slab is square and the finish is intact, a repair makes sense and is the less expensive route. If the panel is warped past tolerance, rotted past the threshold, or the glass unit is failed in a style where the glass isn’t serviceable, we’ll tell you replacement is the honest move, and we’ll quote it the same way: upfront, in writing, no pressure. Call (850) 801-5596 for an exact quote, and the estimate is free.
Yes, most of the time. Therma-Tru uses a limited palette of factory finishes on the Classic-Craft and Fiber-Classic lines, and we source the exact paint code through the model and manufacturing plant code on the door’s registration sticker. For older doors with faded original finish, we color-match on site. You’ll never see a repair line on a roof cap if we can avoid it.
The roof cap is the composite piece at the top of a fiberglass or Classic-Craft door slab that seals the panel’s top edge. The roof-scalp flashing is the aluminum piece over the top of a sliding patio door frame that directs water away from the header. They fail in different ways, and Palm Beach humidity and salt air shorten both. If you know which one you’re calling about, great; if not, we’ll figure it out in the inspection.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Palm Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.