Andersen Door Installation Nationwide | TruePane Windows & Doors

Andersen Door Installation in Palm Beach: What to Know First

Andersen door installation in Palm Beach is work we handle as an independent Andersen service provider, and most jobs are completed in a single visit. A typical swing or French door set runs from $1,200 to $4,800 installed depending on the line, the opening condition, and whether you’re working with a 200 Series, 400 Series, E-Series, or A-Series unit. Call (850) 801-5596 and we’ll give you an honest price before any work begins.

Call (850) 801-5596

This page is for homeowners who already own an Andersen door, or are about to buy one, and want it installed by a crew that knows the frames, the flange systems, and the failure points that show up in this climate. If you’ve lived with a door that binds in the humidity or won’t seal against the afternoon downpour, you’re in the right place. We’ve been setting doors in Palm Beach County since 2008, and we’ve seen every way a door installation can go sideways.

How Andersen Products Fail - and How We Fix Them

Andersen makes a solid product, but every door line has its weak spots. Here’s what we actually see in Palm Beach homes:

• 400 Series Frenchwood gliding and hinged doors: sagging panels and sticking thresholds. The 400 Series uses a pine core with a wood veneer, and years of Palm Beach humidity will make the stiles swell and the hinges work loose. The door starts dragging across the threshold in June and won’t latch by September. We reset the hinges, re-shim the jamb where the rough opening has settled, and re-mount the threshold so the weatherstrip compresses evenly. A quick “plane the bottom” fix only works for a season; we correct the alignment so it lasts.
• 200 Series Narroline and Perma-Shield storm doors: failed compression sweep and torn screen tracks. These are the workhorse storm doors on older Palm Beach ranch homes. The bottom sweep loses its memory, the closer bracket wallows out the screw holes, and the screen rail gets a ripple from kids and dogs. We replace with OEM sweep stock, re-drill the closer with through-bolts where the jamb allows, and swap the screen rail without disturbing the glass panel.
• E-Series and A-Series hinged patio doors: weatherstrip gaskets that harden at the corners. These are aluminum-clad lines built for higher-end homes, and the weak point is the corner where the sill and side seals meet. Salt air and reflected heat from a pool deck will crack that gasket in three to five years. Water gets under the sill pan, and you’ll see a stain on the interior floor tile. We pull the panel, clean the sill deck, replace the gasket with factory-spec material, and re-glaze the corner joint before it re-presents itself.
• Architectural and custom Andersen doors: out-of-plumb rough openings. Custom doors get ordered to a tenth of an inch, and the framing is rarely that honest after twenty years. We find open corners and racked headers that bind the latch side and leave a daylight gap at the top strike. We re-frame the opening, install a new pressure-treated buck where the slab has settled, and set the door square before the trim ever goes back on.
• Andersen storm doors in salt-exposure zones: corroded hinge bearings and worn closers. If your door faces east toward the Intracoastal, the hinges will start to grind within a few years. The closer arms get stiff from salt film and lose their hold-open. We replace bearings with stainless pins, flush and lubricate the closer, and adjust the closing speed so the door doesn’t slam into a standing jamb. Small fix, but it’s the difference between a door that behaves and one you have to fight every time you walk out.

Our Andersen Door Installation Process

Here’s how a typical job goes, from the first call to the last sweep of the floor:

1. 1
   You call (850) 801-5596 and a live person answers. We ask about the door, the symptoms, and when it was installed. We’ll tell you honestly if this is something we can fix or if a replacement makes more sense.
2. 2
   Our technician measures every opening twice. That means plumb, level, square, and the reveal on all four sides. We’re not measuring for a quote; we’re measuring for the day we install.
3. 3
   We sit down with you on paper. We’ll quote OEM parts side by side with quality aftermarket options where they exist, and we’ll tell you which ones make sense for your door and which ones are wasted money.
4. 4
   We install to the manufacturer’s installation guide and our own standard above it. Shims set on studs, not on drywall. Sill pans flashed to the drainage plane. Hinges torqued, not just driven tight. Everything done the way the manufacturer intended and the way Dale Kessler insists it be done.
5. 5
   We test the full swing, the latch, the deadbolt, the sweep, and the seal. We’ll have you operate the door before we leave, and we won’t call it done until you’re satisfied it works the way it should.
6. 6
   Both warranty layers get registered in writing before we leave the driveway. That’s The Keystone Standard, and it’s on every single job. If something isn’t right within 90 days, we come back and make it right. No paperwork fights, no arguing.

What Andersen Door Installation Costs in Palm Beach

Most Andersen door installation work in Palm Beach falls into these ranges:

• Storm door installation: $450-$950, depending on the closer hardware and whether the opening needs shimming or new trim.
• Entry swing door (200 or 400 Series, pre-hung): $1,200-$2,800, including re-setting the opening and new weatherstripping.
• French double door (400 Series or E-Series): $2,200-$4,800, with hinge adjustments, threshold replacement, and re-flashing where needed.
• Custom or architectural door (A-Series, E-Series, or an arched frame): $3,500-$8,000 or more, depending on the rough opening work and hardware.

The price moves based on how far out of square the opening is, whether the hinge pockets are wallowed out, what the sill pan looks like, and whether you’re staying with OEM hardware. We give a written line-item quote before work starts, and that number doesn’t change unless we find rot that has to be addressed. Call (850) 801-5596 for a free estimate on your Andersen door.

Why Palm Beach Homeowners Call TruePane Windows & Doors for Andersen Work

Palm Beach has no shortage of contractors who will hang a door. We’re not after the one-and-done job; we’re the company that plans to be here in thirty years. Dale Kessler started TruePane Windows & Doors out of a principle that out-of-true installs and voided warranties were problems worth fixing permanently. The Done Right Promise is our answer: if it’s not done right, we make it right. The Keystone Standard means both manufacturer warranty layers get registered in writing, with durations stated, before our truck leaves your driveway.

Our technicians are background-checked and uniformed, and they measure every opening twice. Beyond, we’re authorized installers for, PGT, and CGI lines, so if the best answer for your opening is a different brand, we’ll tell you that and quote both side by side. A live person answers our phone 24/7, and most jobs are done in one visit. Done right, on paper, no surprises on the bill.

Frequently Asked Questions