Mr-Glass Custom & Geometric Windows Nationwide | TruePane Windows & Doors

Mr-Glass Custom & Geometric Windows in Palm Beach: What to Know First

We repair, replace, and install Mr-Glass custom and geometric windows throughout Palm Beach, and most jobs are quoted within 24 hours and completed in a single visit. As an independent Mr-Glass service provider, we charge a fair market rate for the work, not a franchise markup, and every quote is written line-by-line before any tools come off the truck. If you own a Mr-Glass arched transom, a radius window over a front entry, or a large trapezoid fixed unit that has started fogging or binding, this page will tell you what’s actually going on and what it costs to set it straight. Call (850) 801-5596 and a real person answers, any hour.

Call (850) 801-5596

Key Takeaways

• Mr-Glass geometric units fail at the seal and the frame corner joint more often than the glass itself, especially in Palm Beach’s salt air and summer humidity.
• Warranty work stays valid when we use OEM or warranty-safe equivalent components and register every layer in writing.
• Most custom-shaped repairs run between $220 and $1,200 depending on the shape, glazing, and access; full replacements of large radius units start around $1,800.
• TruePane is not affiliated with Mr-Glass. We are an independent Palm Beach window contractor that services and replaces Mr-Glass product the same way we do PGT, CGI, CWS, and ES Windows.

How Mr-Glass Products Fail - and How We Fix Them

Mr-Glass builds a solid mid-tier frame, but custom shapes put stress in places a square window never feels. Then Florida adds heat, salt, and hurricane-season moisture. Here is what we actually see in Palm Beach homes, unit by unit.

• Radius and arched unit seal fog at the apex. Mr-Glass radius windows put the heaviest bend in the glass at the top of the arch. After eight to ten years of thermal cycling, the low-E coating and the spacer bar start to separate right at that curve. You will see a crescent of fog that never dries. We replace the insulated glass unit with a matched radius IG, not a field-cut square that someone forces into the opening.
• Trapezoid and parallelogram frames open up at the lower corner joint. The angled frame members in Mr-Glass custom shapes carry weight unevenly. In taller openings, say a two-story stairwell, the lower obtuse corner slowly works loose. The sash drops a few millimeters, daylight shows through the weatherstrip, and the locking pins no longer align. We disassemble the corner, re-square the frame with new corner keys, and bed the joint properly.
• Impact-rated Mr-Glass units show sealant blistering along the mullion joints. On multi-lite geometric assemblies, the slim-line mullions between lites are a known weak point. Palm Beach sun raises surface temperatures past what an older sealant bead can hold, and it blisters. Water wicks in behind the trim. We strip the old bead, inspect the mullion for corrosion, and re-seal with a marine-grade silicone rated for coastal exposure.
• Obscure and decorative glass in Mr-Glass half-rounds turns cloudy at the edge. The acid-etched or patterned glass used in entry transoms sometimes has micro-pores along the cut edge. Humidity gets in, and a gray film creeps inward from the frame. It looks like a failed seal but it is the glass edge. We confirm with a moisture meter and replace the lite with a properly edged and capped unit.
• Mr-Glass casement hardware on shaped operable units binds after storm-season swelling. The geometric operating sashes use compact hinge mechanisms that are less forgiving than a standard casement hinge. After a wet September, the wood or composite frame swells and the operator arm fights the sash. Owners crank harder, the gear strips, and the window will not seal. We realign or replace the hinge and operator together so the sash seats flat again.

Our Mr-Glass Custom & Geometric Windows Process

1. 1
   Call and talk to a live person. You describe the window and the symptom. We ask about the shape, approximate size, and whether it is an impact unit. We schedule a visit.
2. 2
   Measure and diagnose on site. A uniformed technician shows up, lays eyes on the unit, checks the seal, the frame joint, and the glazing. Every opening is measured twice. Dale Kessler grew up in El Cid and was trained at Palm Beach State College by shop instructors who were particular about sealant depth and frame tolerances. That particularity still runs our diagnostics.
3. 3
   Parts decision on paper. If the unit needs a new IG, new hardware, or a full frame, we quote OEM first when it is available and sensible. If OEM is six weeks out and the window is leaking, we offer a warranty-safe equivalent with the trade-offs written plain. You see both options side by side before you commit.
4. 4
   The repair or replacement. We work on the unit in place where possible. Full replacements come out clean, and the new Mr-Glass or equivalent unit is set to the same reveal and weatherproofing standard we use on new construction.
5. 5
   Test and register. We check for daylight, drafts, and binding. Then we register both warranty layers in writing before the truck leaves the driveway. That is the Keystone Standard, and it applies to every Mr-Glass job.
6. 6
   Cleanup and follow-through. The old glass and hardware leave with us. You get a written summary of the work, the warranty durations, and the Done Right Promise in hand.

What Mr-Glass Custom & Geometric Windows Costs in Palm Beach

Here are the ranges we quote most often in Palm Beach. Every job gets a written line-item estimate before work begins, so the number you approve is the number you pay.

• IG replacement in a fogged radius or half-round unit: $280 to $620 depending on the bend radius and glass package.
• Frame corner repair and re-square on a trapezoid or parallelogram: $220 to $480.
• Full replacement of a fixed geometric unit, standard glazing: $1,200 to $2,400 installed.
• Full replacement of an impact-rated geometric unit: $2,200 to $4,800 depending on size, shape, and PSI rating.
• Mullion re-seal on a multi-lite geometric assembly: $180 to $400 per mullion line.
• Hardware replacement on an operable shaped casement: $190 to $390 including realignment.

What moves the price is the bend radius on curved glass, whether the unit is impact-rated, access from a ladder or lift, and the condition of the frame. A window that can be repaired keeps its cost down. A window that has been binding for years has usually damaged its own frame and costs more. Call (850) 801-5596 for a free estimate and we will tell you straight which side of that line your unit is on.

Why Palm Beach Homeowners Call TruePane Windows & Doors for Mr-Glass Work

Most window companies in Palm Beach do not want to touch a Mr-Glass radius unit that someone else installed eight years ago. The angles are odd, the parts are not always stocked at the supply house, and the liability sits on the installer. We do the work anyway, and we stand behind it. Every job carries the Done Right Promise. If the pane is not true, the job is not done, and we come back and make it right without arguing about whose fault it was. Our technicians are background-checked and uniformed, and they work in your home the way they would work in their own mother’s. As an independent Mr-Glass service provider we are not bound to one parts channel, which means we can source what your unit actually needs. And when a Mr-Glass fixed unit is beyond saving, we quote replacements across PGT, CGI, CWS, and ES Windows on the same page so you can compare without sitting through three more appointments.

FAQs